Minnesota DVS CDL General Knowledge Practice Test 3
Test 3 of 5. Pick an answer for each question to see if it is right and why; your score appears at the end. You need 40 correct answers to pass, the same ratio as the real Minnesota test.
- Questions50
- Correct to pass40
- Passing score80%
- Minimum age18 years
-
1. How do you avoid the sharp lurch that comes at the very end of a stop in a heavy vehicle?
Show answer
Answer A: Ease off the brake pressure just before the vehicle actually comes to rest
A smooth stop is finished by reducing pedal pressure as the vehicle settles, so the suspension does not rock the cab and the load forward.
-
2. You are hauling an open box of loose gravel. What does that load require?
Show answer
Answer A: A cover, so that material cannot blow off or spill onto the road
Loose material that can be blown or spilled has to be covered so it does not come out of the body and strike traffic behind.
-
3. What does safe practice require of a commercial driver who wants to eat, drink or read a delivery note?
Show answer
Answer B: Handle it before or after driving, not while moving
Anything that takes hands, eyes or attention away from the task belongs outside the driving time, not inside it.
-
4. While double clutching, what goes wrong if you take too long between the two clutch movements?
Show answer
Answer A: Engine speed falls too far and the gear becomes hard or impossible to engage
Double clutching only works while engine speed and road speed still match; a slow shift lets rpm drop away and the gear will not go in.
-
5. An automatic transmission is left in its normal drive position as the vehicle rolls down a long grade. What does it tend to do?
Show answer
Answer A: Shift up as road speed rises, so engine braking falls away
An automatic left in drive keeps upshifting as speed builds, which is the opposite of what you want on a grade; that is why the driver must select a low range.
-
6. Why does a load of live animals need special attention?
Show answer
Answer D: The animals move and lean, so the center of gravity shifts and the vehicle can be pushed off balance in a turn
A live load will not stay where it is put, and that movement changes the balance of the vehicle exactly when a curve is loading it most.
-
7. Why does a cracked frame rail or cross member make a vehicle unsafe?
Show answer
Answer B: The frame carries the whole load, and a crack can spread until the structure fails
The frame is the backbone that supports the body, the load and the running gear, so a crack in it is a structural failure that grows with every mile.
-
8. Within total stopping distance, what exactly is perception distance?
Show answer
Answer D: The distance traveled from the moment your eyes see a hazard until your brain identifies it
Perception distance covers only the time between seeing a hazard and recognizing it as a hazard, before any physical reaction begins.
-
9. May a commercial driver use a hand-held phone while stopped at a red light?
Show answer
Answer B: No, a stop in traffic still counts as driving
Hand-held use is allowed only when the vehicle has been moved to the side of or off the highway and halted where it can safely remain stopped.
-
10. How do you test for leaks in a hydraulic brake system during the pre-trip inspection?
Show answer
Answer A: Pump the pedal three times, then hold firm pressure for five seconds and make sure the pedal does not move
If the pedal sinks while you hold pressure, fluid is escaping or air is in the lines, and the vehicle must not be driven until the problem is repaired.
-
11. What alcohol concentration makes it a crime to drive a commercial motor vehicle in Minnesota?
Show answer
Answer B: 0.04 or more
Minnesota Statutes 169A.20 sets the commercial motor vehicle threshold at 0.04, half of the limit that applies to other drivers.
-
12. Your vehicle is stopped just past a hill or curve that hides it from approaching traffic. How should the warning devices be adjusted?
Show answer
Answer A: Move the rearmost device farther back, up to 500 feet, so drivers are warned before the obstruction
When a hill or curve blocks the view, the farthest device is moved back beyond the obstruction so approaching drivers see the warning in time.
-
13. Which items belong to the trailer part of the walkaround inspection?
Show answer
Answer D: Landing gear, doors, tires, wheels, lights, reflectors, frame and cargo securement
The trailer has its own running gear, lighting, structure and load, and all of it is the responsibility of the driver pulling it.
-
14. A doctor prescribes you a medicine that can cause drowsiness. What should you do?
Show answer
Answer A: Tell the doctor what you drive and not drive while affected
Both prescription and over the counter medicines can make a driver unsafe, so the medical professional must know the job and the driver must stay out of the seat while affected.
-
15. You are backing a tractor-trailer in a straight line and the trailer starts to drift to the left. What is the standard correction?
Show answer
Answer D: Turn the top of the steering wheel a little to the left, toward the drift
Small corrections made in the direction the trailer is drifting bring it back into line; large or opposite movements make the drift worse.
-
16. Why does a heavy vehicle need a much larger gap than a car in order to cross or enter traffic?
Show answer
Answer C: Because it accelerates slowly and needs far more road and time to clear the intersection
Slow acceleration combined with the length of the vehicle means a gap that would feel comfortable in a car is nowhere near enough.
-
17. A car ahead of you keeps drifting within its lane and moving unevenly. What should you assume?
Show answer
Answer C: The driver may be distracted, lost or impaired
Unsteady lane keeping is a classic clue to a driver who is not in full control, so the safe response is to keep back and give plenty of room.
-
18. What is the best practice when fog is thick enough to hide the road ahead?
Show answer
Answer B: Slow down before entering the fog, and if visibility is too poor, pull off into a rest area or truck stop until it improves
The safest choice in heavy fog is not to be driving in it, and if you are already in it your speed has to come down before your visibility does.
-
19. Your speedometer stops working during the pre-trip check. How should it be treated?
Show answer
Answer D: As a defect, because the driver cannot judge and control speed without it
A working speedometer is required equipment, because judging speed by feel in a heavy vehicle is unreliable and speed governs stopping distance.
-
20. At a rest area you find that the load has shifted although the straps still feel tight. What should you do?
Show answer
Answer C: Correct the load before driving on, since a shifted load is no longer secure
Movement means the securement has already failed once, and a load that has shifted can shift again, so it is put right before the vehicle moves.
-
21. Why should you never back under a trailer whose landing gear is resting on soft or muddy ground?
Show answer
Answer C: The landing gear can sink or collapse and the trailer can drop or tip over
Soft ground lets the landing gear sink under the load being transferred to it, and a trailer that drops or topples during coupling is extremely dangerous.
-
22. Under federal rules, which commercial vehicles must stop at every railroad crossing before proceeding?
Show answer
Answer D: Passenger buses and placarded hazardous materials vehicles
Buses carrying passengers and vehicles required to display hazardous materials placards must stop at crossings, while other commercial vehicles slow and check.
-
23. You are about to back across a quiet street into a driveway. Which of these is good practice before you start to move?
Show answer
Answer B: Turn on the four-way flashers and sound the horn to alert anyone nearby
Warning other road users and pedestrians before a reverse maneuver gives them the chance to stop or move clear before the vehicle starts back.
-
24. What is the main purpose of a retarder fitted to a heavy vehicle?
Show answer
Answer B: To help slow the vehicle and reduce the need to use the service brakes
Exhaust, engine, hydraulic and electric retarders all slow the vehicle so the brakes stay cool and wear less, especially on grades.
-
25. The brake pedal goes to the floor in a vehicle with hydraulic brakes. What can you do to build some braking pressure?
Show answer
Answer B: Pump the brake pedal rapidly, which may bring back enough pressure to slow the vehicle
Pumping can restore some hydraulic pressure; along with downshifting and the parking brake it is one of the ways to stop when the pedal fails.
-
26. Why should a driver avoid shifting gears in the middle of a turn at an intersection?
Show answer
Answer D: Shifting during the turn takes a hand off the wheel and can cost you control
Pick the gear before you begin turning; shifting in the turn removes a hand from the wheel and can interrupt power just when you need steady control.
-
27. Why must cargo also be held down against vertical movement and not only against sliding?
Show answer
Answer D: Because a load that bounces can jump the blocking and slacken its own tiedowns
Rough road makes an unrestrained article lift; every bounce lets it move a little and works the tiedowns loose until nothing is holding it.
-
28. You are asked to drive a truck loaded with enough hazardous materials to require placards. What must you have?
Show answer
Answer C: A hazardous materials endorsement on your commercial driver license
Driving a vehicle that must be placarded requires the H endorsement, which involves a separate knowledge test and a security background check.
-
29. What is the purpose of the torque rods or radius rods you check on the suspension?
Show answer
Answer A: They hold the axle in alignment with the frame under braking and acceleration
Torque rods resist the twisting and fore and aft forces on the axle, so a cracked or missing rod lets the axle move out of alignment.
-
30. What is the coupling device weight rating on a vehicle?
Show answer
Answer A: The most weight that the coupling on the vehicle is rated to pull
The coupling device rating is a limit on how much weight the coupling may tow, and it is one of the ratings that has to be respected when a combination is loaded.
-
31. Where are regrooved, recapped or retreaded tires not allowed on a truck or truck tractor?
Show answer
Answer C: On the front steering wheels
Regrooved and retreaded tires are prohibited on the front wheels of a truck or truck tractor because a steering tire blowout is extremely difficult to manage.
-
32. Which drivers does Minnesota exempt from the requirement to hold a commercial driver's license?
Show answer
Answer A: Farm truck drivers operating within 150 miles of the farm
Minnesota waives the CDL requirement for qualifying farm trucks used within 150 miles of the farm, along with authorized emergency vehicles and recreational vehicles used for personal purposes.
-
33. What is the correct order for a double clutch downshift?
Show answer
Answer D: Release the accelerator and push the clutch to reach neutral, release the clutch and press the accelerator to raise engine speed, then push the clutch again and select the lower gear
A lower gear turns faster than the one being left, so engine speed has to be raised in neutral before that gear will engage cleanly.
-
34. You are about to slow down sharply on a highway to make a turn into a narrow driveway. How can you warn the drivers behind you?
Show answer
Answer C: Tap the brake pedal a few times so the brake lights flash before you slow down
A few light taps flash the brake lights and give following drivers an early warning that you are about to slow or stop.
-
35. After two hours of driving you measure a tire and the pressure reads higher than the cold figure. What should you do?
Show answer
Answer B: Nothing, because pressure rises normally as a tire heats up in use
Air expands as the tire heats, so a higher hot reading is expected, and letting air out leaves the tire underinflated once it cools.
-
36. Your right wheels drop off the pavement onto a soft shoulder. What is the correct recovery?
Show answer
Answer A: Stay on the shoulder, ease off the accelerator, brake gently only once speed is down to about 20 mph, then steer back sharply and countersteer at once
Bringing speed down on the shoulder first avoids a violent sideways jolt, and countersteering the instant the tires are back on the pavement keeps the vehicle out of the next lane.
-
37. Part of looking well ahead is planning an out. What does that mean?
Show answer
Answer B: Keeping an escape path in mind in case traffic stops suddenly
Because a heavy vehicle often cannot stop in time, good drivers continuously note where they could steer if the space ahead closes.
-
38. What is normally required in order to move an over-width or over-length load?
Show answer
Answer B: A special permit along with warning devices such as flags and signs
Oversize movements need a permit plus marking devices, and travel is often limited to certain hours or routes.
-
39. The coolant temperature gauge climbs above its normal range on a long grade. What is the correct response?
Show answer
Answer C: Stop when it is safe to do so and find the cause before going on
Rising coolant temperature signals a fault such as a lost belt, a leak or a blocked radiator, and continuing can turn a repair into a destroyed engine.
-
40. Total stopping distance is made up of which parts?
Show answer
Answer A: Perception distance, reaction distance and braking distance
The vehicle travels while the hazard is recognized, while the driver moves to the pedal, and again while the brakes slow the vehicle.
-
41. What are you looking for when you check the drive belts in the engine compartment?
Show answer
Answer C: That each belt is snug and free of cracks, frays or heavy wear
A loose or cracked belt can break and stop the fan, the water pump or the alternator, which leads quickly to overheating or a dead electrical system.
-
42. Which vehicle condition makes hydroplaning more likely?
Show answer
Answer C: Tires that are worn or underinflated
Tread depth and correct pressure are what let a tire push water aside, so worn or soft tires lift onto the water film at lower speeds.
-
43. Loading heavy freight on top of lighter freight has what effect on the vehicle?
Show answer
Answer B: It raises the center of gravity and makes a rollover more likely
A high center of gravity lets the vehicle tip more easily in curves or during a sudden swerve.
-
44. What is checked in step six of the seven-step method?
Show answer
Answer D: The turn signals and the stop lights, checked from outside the vehicle
Step six returns to the cab to switch on the signal and stop lamps, then checks each one from outside, because those lamps are not lit during the earlier light check.
-
45. At 55 mph, about how far does a vehicle travel during a typical 3/4 second perception time plus 3/4 second reaction time, before the brakes even begin to work?
Show answer
Answer C: About 120 feet
Each 3/4 second at 55 mph covers about 60 feet, so perception and reaction together use up roughly 120 feet before braking starts.
-
46. How long must a motor carrier keep a driver vehicle inspection report and the certification of repairs?
Show answer
Answer B: Three months
The original report and the certifications attached to it are kept on file for three months from the date the report was prepared.
-
47. Which steering system findings count as defects during the inspection?
Show answer
Answer C: Bent, loose or broken column parts, arms, drag links or tie rods, and missing nuts, bolts or cotter keys
Every joint and fastener between the steering wheel and the tires carries the driver commands, so looseness or a missing retainer can end in a complete loss of steering.
-
48. On a scale, your loaded truck is well under the gross weight limit, but one axle is above the limit for that axle. What does this mean?
Show answer
Answer D: The vehicle is overloaded and the load must be shifted or reduced before you drive on
Each axle and axle group has its own limit and each must be respected; being under the gross limit does not excuse an overloaded axle.
-
49. For an unblocked article longer than 10 feet, the minimum is two tiedowns plus how many more?
Show answer
Answer B: One more for every additional 10 feet of length or any part of 10 feet
Past the first 10 feet, one more tiedown is added for each additional 10 feet of length or any fraction of that distance.
-
50. How does overloading affect the way a vehicle drives?
Show answer
Answer C: It slows the vehicle on upgrades, makes stopping take longer and can overheat the brakes on downgrades
Extra weight demands more from the engine and the brakes, so the vehicle climbs slowly and needs much more distance to stop.