Minnesota DVS CDL General Knowledge Practice Test 9
- Questions50
- Correct to pass40
- Passing score80%
- Minimum age18 years
-
1. How does bracing differ from blocking when securing cargo?
Show answer
Answer B: Bracing runs from the upper part of the cargo to the floor or walls to keep it from moving, while blocking fits snugly against the cargo
Blocking is shaped to fit against the front, back or sides of a piece of cargo; bracing supports it from above so it cannot tip or shift.
-
2. Before raising the hood to inspect the engine compartment, what should you do?
Show answer
Answer B: Shut off the engine, set the parking brake and chock the wheels if needed
The engine compartment is inspected with the engine off and the vehicle secured so nothing can move or turn while your hands are inside.
-
3. A strap is a little too long, so a driver ties a knot in it to take up the slack. Is that acceptable?
Show answer
Answer C: No, tiedowns must not contain knots
A knot destroys the rated strength of a tiedown, so the rules do not allow knotted securement devices; the excess is taken up by the winch or ratchet instead.
-
4. What must a written driver vehicle inspection report cover at the end of the day?
Show answer
Answer C: Any defect or deficiency that would affect safety or could cause a mechanical breakdown
The report identifies the vehicle and lists defects that affect safe operation or could lead to a breakdown, so they are repaired before the next trip.
-
5. What is the first step of the standard seven-step vehicle inspection?
Show answer
Answer C: A general overview of the vehicle, including the last inspection report
The routine opens with a walk-up overview of the vehicle and a review of the previous inspection report so known defects are addressed first.
-
6. Where are the OVERSIZE LOAD signs normally carried on a vehicle moving under such a permit?
Show answer
Answer A: On the front and the rear of the vehicle
The warning signs face the traffic that meets the load and the traffic that comes up behind it, so they go on the front and the rear.
-
7. Which factors determine a safe speed for a long, steep downgrade?
Show answer
Answer C: The steepness and length of the grade, the weight of the vehicle and cargo, and the road and weather conditions
Gravity, weight and traction all decide how fast a heavy vehicle can safely descend, which is why signs often post lower speeds for trucks on grades.
-
8. What must the motor carrier do about a defect listed on a driver vehicle inspection report?
Show answer
Answer D: Repair it, or certify that repair is not needed, before the vehicle is dispatched again
A reported defect must be corrected, or certified as not needing correction, and that certification is what the next driver reads before taking the vehicle.
-
9. You are driving past a park where children are playing close to the curb. What is the correct assumption?
Show answer
Answer A: A child may run into the street without looking
Children act on impulse and do not judge traffic well, so a driver has to expect one to enter the road and slow down in advance.
-
10. A fire has started in the vehicle. How should the extinguisher be used?
Show answer
Answer B: Stay as far back as the reach of the extinguisher allows, stand upwind, and aim at the base of the fire
Aiming at the base attacks what is actually burning, and staying upwind and well back protects the driver from heat, smoke and the flames themselves.
-
11. In a vehicle with a manual transmission, when should the clutch be pushed in during a normal stop?
Show answer
Answer A: Just before the engine would stall, when the vehicle is nearly stopped
Staying in gear until the last moment keeps engine braking and steady control, so the clutch goes down only when the engine is about to drop below idle.
-
12. What does the gross combination weight rating cover?
Show answer
Answer B: The maximum loaded weight of the power unit together with the trailer or trailers it tows
The combination rating takes in the power unit and everything behind it, loaded, as specified by the manufacturer.
-
13. While double clutching, what goes wrong if you take too long between the two clutch movements?
Show answer
Answer A: Engine speed falls too far and the gear becomes hard or impossible to engage
Double clutching only works while engine speed and road speed still match; a slow shift lets rpm drop away and the gear will not go in.
-
14. You are given a ratchet strap with a deep cut along one edge. What should you do?
Show answer
Answer C: Do not use it; a damaged tiedown cannot be relied on to hold its rated load
Cuts, burns, knots and broken stitching weaken a strap far below its marked working load limit, so it must be taken out of service.
-
15. What does it mean to overdrive your headlights at night?
Show answer
Answer D: Driving so fast that you cannot stop within the distance lit by your headlights
You must be able to stop inside the distance you can see; at night that distance is limited by the headlights, so speed must be lowered to match.
-
16. Where do you find the maximum weight a tire can safely carry?
Show answer
Answer D: Stamped on the sidewall of the tire itself
Each tire is marked with the greatest weight it can carry at a stated inflation pressure, and the load on an axle must stay within the total for its tires.
-
17. Which combination of warning devices meets the requirement for a stopped commercial vehicle?
Show answer
Answer A: Three reflective triangles, or six fusees, or three liquid burning flares
A vehicle may carry three bidirectional reflective triangles, six fusees or three liquid burning flares as its warning devices.
-
18. At what time of day do drowsy driving crashes occur most often?
Show answer
Answer A: Between midnight and 6 a.m.
The body clock makes people sleepiest in the early morning hours, which is when most fatigue-related crashes happen.
-
19. Your drive wheels start to spin and the rear begins to slide while you accelerate on a slick surface. What should you do?
Show answer
Answer B: Stop accelerating and, if the vehicle has a manual transmission, push in the clutch
An acceleration skid ends when the drive wheels stop pushing, so easing off the throttle and disengaging the clutch lets them regain grip.
-
20. You press on a drive belt and it deflects far more than the others. What does that suggest?
Show answer
Answer C: The belt is too loose and the part it drives may not work properly
A belt with excessive play slips on its pulleys, so the accessory it drives turns too slowly or not at all under load.
-
21. During the walkaround you find the reflective conspicuity tape along the trailer caked with road grime. What should you do?
Show answer
Answer B: Clean it, because dirty reflective material cannot make the trailer visible at night
Reflective sheeting only works if light can reach it and bounce back, so a dirty strip leaves the trailer effectively unmarked to approaching traffic.
-
22. On the Interstate System, what is the federal maximum weight allowed on a single axle?
Show answer
Answer A: 20,000 pounds
Federal limits for the Interstate System cap one single axle at 20,000 pounds.
-
23. What is the risk when too little weight rests on the drive axles?
Show answer
Answer A: Poor traction, so the drive wheels spin easily on wet or slippery surfaces
Traction depends on weight pressing the driving tires onto the road, so a light drive axle spins on wet, snowy or loose surfaces.
-
24. In the seven-step method, what comes immediately after starting the engine and inspecting inside the cab?
Show answer
Answer D: Turn off the engine and check the lights
Step four shuts the engine down and switches on the lamps needed for driving so the driver can leave the cab and confirm they actually work.
-
25. Your truck has a backup alarm that sounds whenever reverse is selected. What may a driver rely on it for?
Show answer
Answer D: Very little; it warns some people but cannot show you what is behind the vehicle
An alarm may not be heard over yard noise or by someone wearing hearing protection, so it never replaces looking at the path yourself.
-
26. A brake light lens is cracked and the lamp still lights. How should that be treated?
Show answer
Answer B: As a defect, because water can enter and the lamp can dim or fail
A cracked lens lets in water and dirt, which corrodes the socket and dulls the lamp, so it is reported before it becomes a dead brake light.
-
27. Which of these is NOT on the federal list of parts and accessories the driver must be satisfied are in good working order before driving?
Show answer
Answer D: The seat cushion upholstery
The federal pre-trip rule names brakes, steering, lights and reflectors, tires, horn, wipers, mirrors, coupling devices, wheels and rims, and emergency equipment; seat upholstery is not on that list.
-
28. In very hot weather, how often should you check the tires during a trip?
Show answer
Answer D: About every two hours or every 100 miles
Heat raises tire pressure and can lead to blowouts, so tires are checked about every two hours or 100 miles when it is very hot.
-
29. During the walkaround you notice one tire on an axle is a radial and the tire next to it is bias-ply. What should you do?
Show answer
Answer B: Treat it as a defect, because radial and bias-ply tires must not be mixed on the same axle
Radial and bias-ply tires flex and grip differently, so mixing them on one axle makes the vehicle handle unpredictably and is not allowed.
-
30. What is the correct order for a double clutch downshift?
Show answer
Answer D: Release the accelerator and push the clutch to reach neutral, release the clutch and press the accelerator to raise engine speed, then push the clutch again and select the lower gear
A lower gear turns faster than the one being left, so engine speed has to be raised in neutral before that gear will engage cleanly.
-
31. You are moving an oversized load under a permit that requires a pilot vehicle. What is the pilot vehicle there to do?
Show answer
Answer B: Warn other traffic and check the route ahead for clearances and hazards
Escort or pilot vehicles warn approaching traffic and scout the route for low bridges, narrow spots and other hazards that a wide or long load cannot pass.
-
32. Why do worn tires lose grip so quickly on a wet road?
Show answer
Answer D: Shallow tread cannot move water out from under the tire
The grooves in a tire exist to channel water away so the rubber can touch the road, and a worn tire has lost that capacity.
-
33. How does overloading affect the way a vehicle drives?
Show answer
Answer C: It slows the vehicle on upgrades, makes stopping take longer and can overheat the brakes on downgrades
Extra weight demands more from the engine and the brakes, so the vehicle climbs slowly and needs much more distance to stop.
-
34. Which situations call for a mirror check in a commercial vehicle?
Show answer
Answer A: Every lane change, turn, merge and tight maneuver
Mirrors must be checked regularly and always before, during and after any movement that changes the path of the vehicle.
-
35. How do objects appear in a convex mirror compared with a flat mirror?
Show answer
Answer B: Smaller and farther away than they really are, while a wider area is shown
A convex mirror shows a wider field but shrinks everything in it, so the driver must remember that vehicles are closer than they look.
-
36. Why must you never coast down a hill in neutral or with the clutch pushed in?
Show answer
Answer C: You lose the braking effect of the engine and your brakes may overheat and fail
Engine braking is what keeps a heavy vehicle in check on a grade; coasting throws it away and leaves the service brakes to do all the work until they overheat.
-
37. You pick up a sealed trailer at a shipper. What should you check before leaving the dock?
Show answer
Answer B: That the seal number matches the paperwork and that the doors are properly closed
You cannot look at a sealed load, but you can confirm that the seal is intact, that its number matches the documents and that the doors are secure.
-
38. What is the most common cause of a front-wheel skid, where the vehicle keeps going straight even though you turn the wheel?
Show answer
Answer B: Driving too fast for the conditions
A front-wheel skid usually comes from too much speed for the traction available; the only cure is to let the vehicle slow down and stop turning or braking so hard.
-
39. Besides being uncomfortable, what can a series of hard, jerky brake applications do to a loaded combination?
Show answer
Answer A: Shift the load and push the trailer out of line behind the tractor
Sudden, uneven braking can move cargo forward and upset the alignment of a trailer, which is why stops should be made smoothly.
-
40. What are you looking for when you check the hubs and wheel seals during the walkaround?
Show answer
Answer B: Leaking oil or grease, which can also contaminate the brake linings
A leaking hub seal starves the bearing of lubricant and the escaping oil or grease can soak the brake linings and cut braking power.
-
41. At 55 mph, about how far does a vehicle travel during a typical 3/4 second perception time plus 3/4 second reaction time, before the brakes even begin to work?
Show answer
Answer C: About 120 feet
Each 3/4 second at 55 mph covers about 60 feet, so perception and reaction together use up roughly 120 feet before braking starts.
-
42. A sign before a long descent shows 6 percent. What does that number tell you?
Show answer
Answer A: How steep the grade ahead is
Percent grade is the drop in feet for every hundred feet of road, so the higher the number the faster speed will build and the lower the gear you need.
-
43. A car ahead of you keeps drifting within its lane and moving unevenly. What should you assume?
Show answer
Answer C: The driver may be distracted, lost or impaired
Unsteady lane keeping is a classic clue to a driver who is not in full control, so the safe response is to keep back and give plenty of room.
-
44. Your brakes are starting to fade on a mountain downgrade and a sign shows an escape ramp one mile ahead. What should you do?
Show answer
Answer B: Plan to use the ramp instead of trying to reach the bottom
Fading brakes on a grade only get worse, and the ramp exists precisely so a driver does not have to gamble on the rest of the descent.
-
45. An angry driver has cut in front of you and is now braking hard to provoke you. What is the safest response?
Show answer
Answer D: Drop back, avoid eye contact and let the driver go
Giving an aggressive driver space and no response removes the conflict, while any answering gesture invites escalation you cannot control in a heavy vehicle.
-
46. How does a typical escape ramp stop a runaway vehicle?
Show answer
Answer B: With a bed of loose gravel or sand, often on an upgrade
Escape ramps use deep loose material, usually combined with a rising grade, so the vehicle is slowed gradually instead of being stopped by impact.
-
47. A commercial vehicle stops on the shoulder of an undivided two-lane road that carries traffic in both directions. Where do the warning devices go?
Show answer
Answer B: Within 10 feet of the vehicle, plus 100 feet to the front and 100 feet to the rear
On a two-way road the devices must mark the vehicle itself and warn traffic approaching from each direction, and they must be in place within ten minutes.
-
48. You have stopped and a pedestrian is waiting to cross in front of your truck. Why should you not wave the person across?
Show answer
Answer C: Another driver may not stop, and your wave sends the person into danger
You cannot control what drivers in the other lanes will do, so you should not invite a pedestrian into a lane you do not command.
-
49. What makes a brake hose or air line a defect during the walkaround?
Show answer
Answer D: It is cracked, worn, kinked, or rubbing against another part
A chafed or cracked line can burst under pressure and take the braking on that circuit with it, so damage and rubbing points must be corrected.
-
50. The paperwork shows a weight, but the load looks heavier than you expected. What should you do?
Show answer
Answer C: Weigh the vehicle, since you are the one answerable for driving it overweight
The driver is the one who can be cited for an overweight vehicle, so a doubtful weight is settled on a scale before the trip continues.